Lith-Printing mit Fomabrom

0 Replies, 36284 Views

Ich habe jetzt den Satz Fomabrom von Johannes getestet, und der lithet ohne weiteres. Entweder war der Entwickler von Johannes zu kalt, oder es gab irgendeinen nicht reproduzierbaren Prozessfehler.

Moersch Lith Masterset, 750 ml Wasser, 25 ml A, 25 ml B, 2,5 ml C, 10 D, +4 Blenden, Print im Entwickler ständig bewegen. Bei 23 bis 24 Grad dauert es 5-7 Minuten bis die erste Zeichnung sichtbar ist, die erste Schwärzung zeigt sich in 13-14 Minuten, in 17-18 Minuten ist das Bild fertig. Wenn die Suppe sich abkühlt, dauert alles viel länger.

Sehr schöner, zurückhaltender Ton in den Lichtern (irgendwo in der Gegend von beige, umbra und ocker), Schwarzen sehr (!) könig. Dramatischer Effekt, sieht cool aus aber passt nicht für jedes Bild.

Durch Änderung des Verhältnisses von A und B, kürzere Belichtung und entsprechend weniger C und D, hoffe ich, die Königkeit ein bisschen moderater zu bekommen. Mit Easylith geht das leichter, aber davon habe ich nichts im Vorrat. Hat jemand ein gutes Rezept für Masterset?

Grüße,

Samuli
"No photograph ever was good, yet, of anybody - hunger and thirst and utter wretchedness overtake the outlaw who invented it! It transforms into desperadoes the meekest of men; depicts sinless innocence upon the pictured faces of ruffians; gives the wise man the stupid leer of a fool, and a fool an expression of more than earthly wisdom." (Mark Twain)



http://www.samuli-schielke.de/foto.htm
(This post was last modified: 19-01-2006, 11:10 PM by Samuli Schielke.)

Messages In This Thread
Lith-Printing mit Fomabrom - by Guest - 28-12-2005, 02:07 PM
Lith-Printing mit Fomabrom - by Mirko Boeddecker - 28-12-2005, 04:11 PM
Lith-Printing mit Fomabrom - by Guest - 28-12-2005, 04:33 PM
Lith-Printing mit Fomabrom - by Mirko Boeddecker - 28-12-2005, 05:15 PM
Lith-Printing mit Fomabrom - by Guest - 28-12-2005, 05:27 PM
Lith-Printing mit Fomabrom - by Guest - 05-01-2006, 04:20 PM
Lith-Printing mit Fomabrom - by Guest - 09-01-2006, 12:32 AM
Lith-Printing mit Fomabrom - by Guest - 09-01-2006, 03:13 PM
Lith-Printing mit Fomabrom - by Mirko Boeddecker - 09-01-2006, 11:25 PM
Lith-Printing mit Fomabrom - by Samuli Schielke - 10-01-2006, 03:43 PM
Lith-Printing mit Fomabrom - by Guest - 11-01-2006, 05:20 PM
Lith-Printing mit Fomabrom - by Guest - 11-01-2006, 05:57 PM
Lith-Printing mit Fomabrom - by RWSchueller - 13-01-2006, 04:23 PM
Lith-Printing mit Fomabrom - by Samuli Schielke - 19-01-2006, 11:07 PM



Users browsing this thread: 1 Guest(s)

Theme Selector